Movable cores and side-actions are commonly used on injection molds to make complex geometries possible. While details are more complicated than described here, some simple calculations provide worst-case estimates for proper sizing.
Force on the Core
Before determining the requirements of the side-action, calculating force on the core is essential. Seal offs, core length and other factors notwithstanding, the designer can simply use maximum projected area and injection pressure to calculate core force.
Maximum Projected Area (C) in square inches is found by sectioning the core at the largest point exposed to plastic.
Maximum Injection Pressure (P) is nozzle pressure in psi (hydraulic ram injection pressure x 10).
Core Force (F) = P x C.
For 20,000 psi and a 2″ dia. pin:
F = (20,000 psi)(3.14 sq.in.) = 62,800 lbs.
Side-Action Options
The following side-action options are possible:
1) Cam Pin with Heel-no preload
2) Cylinder with Heel-no preload
3) Cylinder Only-large
4) Side-Action System-small
While methods 1 and 2 use heel blocks to final position the core, flex and compression is often a problem. More robust preloading methods 3 (with pressure) and 4 (without pressure), eliminate these issues, but require the ability to calculate core and cylinder forces.
Cylinder Basics
Cylinder Push/Extend Force (M) and Cylinder Pull/Retract Force (N) is calculated as follows:
M = H x
N = H x [(3.14xB})/4 – (3.14xR2)/4]
H = Hydraulic supply pressure (psi)
B= Bore diameter of cylinder (in.)
R= Rod diameter of cylinder (in.)
Note for pull, rod area subtracts from the piston area. Retract Force is critical when considering friction from material shrinkage.
Cylinder Sizing
Standard Cylinders: If the machine cylinder hydraulic pressure is known (and available during injection), minimum bore size is:
B = SQRT[(4 x F)/(H x 3.14)]
For 2″ dia. core and H = 1,500 psi:
B = SQRT[(4 x 62,800)/(1,500 x 3.14)]= 7.3 inches (8″ bore cylinder)
Nonstandard Cylinders: Preloading side-action cylinders generate the large output forces of large bore cylinders in a smaller bore package. A typical preload side-action system produces 60,000 lbs of output force with a bore diameter of two inches, and total outside diameter of five inches, easily fitting inside bore of the eight-inch standard cylinder in the example. Nonstandard cylinders may also maintain output force with zero psi hydraulic pressure.
Cylinder calculations provide good first look comparisons when considering the most suitable side-action option early in the mold design.
Wow, amazing weblog format! How long have you been running a
blog for? you made blogging glance easy. The whole
look of your web site is wonderful, let alone the content!
Right away I am ready to do my breakfast, once having my breakfast coming
again to read more news.
I couldn’t resist commenting. Very well written!
If some one needs to be updated with hottest technologies therefore he must be go to see this
site and be up to date every day.
Thanks designed for sharing such a nice thought, piece of writing is pleasant, thats why i have
read it entirely
Its such as you read my mind! You seem to grasp
a lot approximately this, like you wrote the ebook in it or something.
I feel that you can do with a few % to drive the message house a little bit, but other than that, this is
magnificent blog. A great read. I’ll definitely be back.
It’s awesome to go to see this web site and reading the views of all friends concerning
this piece of writing, while I am also keen of getting familiarity.
You made some really good points there. I looked on the
internet for more info about the issue and found most people will go along with your views
on this web site.
Greetings! Very useful advice in this particular post!
It’s the little changes that make the most important changes.
Thanks for sharing!
Hi, constantly i used to check webpage posts here early in the dawn, for the reason that i enjoy
to learn more and more.