Movable cores and side-actions are commonly used on injection molds to make complex geometries possible. While details are more complicated than described here, some simple calculations provide worst-case estimates for proper sizing.
Force on the Core
Before determining the requirements of the side-action, calculating force on the core is essential. Seal offs, core length and other factors notwithstanding, the designer can simply use maximum projected area and injection pressure to calculate core force.
Maximum Projected Area (C) in square inches is found by sectioning the core at the largest point exposed to plastic.
Maximum Injection Pressure (P) is nozzle pressure in psi (hydraulic ram injection pressure x 10).
Core Force (F) = P x C.
For 20,000 psi and a 2″ dia. pin:
F = (20,000 psi)(3.14 sq.in.) = 62,800 lbs.
Side-Action Options
The following side-action options are possible:
1) Cam Pin with Heel-no preload
2) Cylinder with Heel-no preload
3) Cylinder Only-large
4) Side-Action System-small
While methods 1 and 2 use heel blocks to final position the core, flex and compression is often a problem. More robust preloading methods 3 (with pressure) and 4 (without pressure), eliminate these issues, but require the ability to calculate core and cylinder forces.
Cylinder Basics
Cylinder Push/Extend Force (M) and Cylinder Pull/Retract Force (N) is calculated as follows:
M = H x
N = H x [(3.14xB})/4 – (3.14xR2)/4]
H = Hydraulic supply pressure (psi)
B= Bore diameter of cylinder (in.)
R= Rod diameter of cylinder (in.)
Note for pull, rod area subtracts from the piston area. Retract Force is critical when considering friction from material shrinkage.
Cylinder Sizing
Standard Cylinders: If the machine cylinder hydraulic pressure is known (and available during injection), minimum bore size is:
B = SQRT[(4 x F)/(H x 3.14)]
For 2″ dia. core and H = 1,500 psi:
B = SQRT[(4 x 62,800)/(1,500 x 3.14)]= 7.3 inches (8″ bore cylinder)
Nonstandard Cylinders: Preloading side-action cylinders generate the large output forces of large bore cylinders in a smaller bore package. A typical preload side-action system produces 60,000 lbs of output force with a bore diameter of two inches, and total outside diameter of five inches, easily fitting inside bore of the eight-inch standard cylinder in the example. Nonstandard cylinders may also maintain output force with zero psi hydraulic pressure.
Cylinder calculations provide good first look comparisons when considering the most suitable side-action option early in the mold design.
Greetings from California! I’m bored to tears at work so I decided to check out your site on my iphone during lunch break.
I enjoy the knowledge you present here and can’t wait to take a look when I get
home. I’m surprised at how quick your blog loaded on my mobile ..
I’m not even using WIFI, just 3G .. Anyways, amazing site!
Thank you for another informative web site. The place else may just I am getting that kind of
information written in such an ideal method? I have a undertaking that I am just now operating on, and I’ve been on the glance out
for such info.
Good article. I absolutely appreciate this website.
Keep it up!
I pay a quick visit every day a few websites and sites to read articles or reviews, except this web
site provides feature based content.
Hey there, I think your website might be having browser compatibility issues.
When I look at your blog site in Chrome, it looks fine but when opening in Internet Explorer, it has some overlapping.
I just wanted to give you a quick heads up! Other then that, terrific blog!
please use a higher IE version, that is OK!
Pretty section of content. I just stumbled upon your web site and in accession capital to assert that I get actually enjoyed account
your blog posts. Any way I will be subscribing to your feeds and even I achievement you
access consistently fast.
I am really impressed with your writing skills as well as with the
layout on your blog. Is this a paid theme or did you modify it
yourself? Anyway keep up the excellent quality writing, it’s rare to see a great blog like this one
today.
I was recommended this website by my cousin. I’m not sure whether this
post is written by him as no one else know such detailed about my problem.
You are amazing! Thanks!
I blog frequently and I really appreciate your information.
The article has truly peaked my interest. I am going to book
mark your site and keep checking for new information about once a week.
I subscribed to your RSS feed too.
Hello there, just became alert to your blog through Google, and found that it’s truly informative.
I’m gonna watch out for brussels. I’ll appreciate if you
continue this in future. A lot of people will be benefited
from your writing. Cheers!