Movable cores and side-actions are commonly used on injection molds to make complex geometries possible. While details are more complicated than described here, some simple calculations provide worst-case estimates for proper sizing.
Force on the Core
Before determining the requirements of the side-action, calculating force on the core is essential. Seal offs, core length and other factors notwithstanding, the designer can simply use maximum projected area and injection pressure to calculate core force.
Maximum Projected Area (C) in square inches is found by sectioning the core at the largest point exposed to plastic.
Maximum Injection Pressure (P) is nozzle pressure in psi (hydraulic ram injection pressure x 10).
Core Force (F) = P x C.
For 20,000 psi and a 2″ dia. pin:
F = (20,000 psi)(3.14 sq.in.) = 62,800 lbs.
Side-Action Options
The following side-action options are possible:
1) Cam Pin with Heel-no preload
2) Cylinder with Heel-no preload
3) Cylinder Only-large
4) Side-Action System-small
While methods 1 and 2 use heel blocks to final position the core, flex and compression is often a problem. More robust preloading methods 3 (with pressure) and 4 (without pressure), eliminate these issues, but require the ability to calculate core and cylinder forces.
Cylinder Basics
Cylinder Push/Extend Force (M) and Cylinder Pull/Retract Force (N) is calculated as follows:
M = H x
N = H x [(3.14xB})/4 – (3.14xR2)/4]
H = Hydraulic supply pressure (psi)
B= Bore diameter of cylinder (in.)
R= Rod diameter of cylinder (in.)
Note for pull, rod area subtracts from the piston area. Retract Force is critical when considering friction from material shrinkage.
Cylinder Sizing
Standard Cylinders: If the machine cylinder hydraulic pressure is known (and available during injection), minimum bore size is:
B = SQRT[(4 x F)/(H x 3.14)]
For 2″ dia. core and H = 1,500 psi:
B = SQRT[(4 x 62,800)/(1,500 x 3.14)]= 7.3 inches (8″ bore cylinder)
Nonstandard Cylinders: Preloading side-action cylinders generate the large output forces of large bore cylinders in a smaller bore package. A typical preload side-action system produces 60,000 lbs of output force with a bore diameter of two inches, and total outside diameter of five inches, easily fitting inside bore of the eight-inch standard cylinder in the example. Nonstandard cylinders may also maintain output force with zero psi hydraulic pressure.
Cylinder calculations provide good first look comparisons when considering the most suitable side-action option early in the mold design.
What’s up to all, how is the whole thing, I think every one is getting
more from this web page, and your views are nice in support of new
visitors.
This is very interesting, You are a very skilled
blogger. I’ve joined your rss feed and look forward to seeking more of your
wonderful post. Also, I have shared your site in my social networks!
hi!,I like your writing so much! proportion we communicate more approximately your post
on AOL? I need an expert in this space to resolve my problem.
Maybe that is you! Looking forward to look you.
I’m impressed, I have to admit. Seldom do I encounter a blog that’s both equally educative
and amusing, and without a doubt, you have hit the nail on the head.
The issue is something which too few folks are speaking intelligently
about. Now i’m very happy that I came across
this in my hunt for something relating to this.
hi!,I really like your writing very so much!
proportion we keep up a correspondence more approximately your article on AOL?
I need a specialist on this house to unravel my
problem. Maybe that is you! Taking a look forward to
peer you.
Hello there! This is my first visit to your blog! We are a team of volunteers and
starting a new initiative in a community in the same niche.
Your blog provided us beneficial information to work on. You have done a outstanding job!
Thanks very interesting blog!
Greetings! Very useful advice within this post! It’s the little changes that
make the most significant changes. Many thanks for sharing!
bookmarked!!, I like your web site!
Every weekend i used to go to see this web page, as i want enjoyment,
as this this web page conations genuinely good funny
stuff too.