Movable cores and side-actions are commonly used on injection molds to make complex geometries possible. While details are more complicated than described here, some simple calculations provide worst-case estimates for proper sizing.
Force on the Core
Before determining the requirements of the side-action, calculating force on the core is essential. Seal offs, core length and other factors notwithstanding, the designer can simply use maximum projected area and injection pressure to calculate core force.
Maximum Projected Area (C) in square inches is found by sectioning the core at the largest point exposed to plastic.
Maximum Injection Pressure (P) is nozzle pressure in psi (hydraulic ram injection pressure x 10).
Core Force (F) = P x C.
For 20,000 psi and a 2″ dia. pin:
F = (20,000 psi)(3.14 sq.in.) = 62,800 lbs.
Side-Action Options
The following side-action options are possible:
1) Cam Pin with Heel-no preload
2) Cylinder with Heel-no preload
3) Cylinder Only-large
4) Side-Action System-small
While methods 1 and 2 use heel blocks to final position the core, flex and compression is often a problem. More robust preloading methods 3 (with pressure) and 4 (without pressure), eliminate these issues, but require the ability to calculate core and cylinder forces.
Cylinder Basics
Cylinder Push/Extend Force (M) and Cylinder Pull/Retract Force (N) is calculated as follows:
M = H x
N = H x [(3.14xB})/4 – (3.14xR2)/4]
H = Hydraulic supply pressure (psi)
B= Bore diameter of cylinder (in.)
R= Rod diameter of cylinder (in.)
Note for pull, rod area subtracts from the piston area. Retract Force is critical when considering friction from material shrinkage.
Cylinder Sizing
Standard Cylinders: If the machine cylinder hydraulic pressure is known (and available during injection), minimum bore size is:
B = SQRT[(4 x F)/(H x 3.14)]
For 2″ dia. core and H = 1,500 psi:
B = SQRT[(4 x 62,800)/(1,500 x 3.14)]= 7.3 inches (8″ bore cylinder)
Nonstandard Cylinders: Preloading side-action cylinders generate the large output forces of large bore cylinders in a smaller bore package. A typical preload side-action system produces 60,000 lbs of output force with a bore diameter of two inches, and total outside diameter of five inches, easily fitting inside bore of the eight-inch standard cylinder in the example. Nonstandard cylinders may also maintain output force with zero psi hydraulic pressure.
Cylinder calculations provide good first look comparisons when considering the most suitable side-action option early in the mold design.
Please let me know if you’re looking for a writer for your
blog. You have some really great posts and I think I would be a good asset.
If you ever want to take some of the load off, I’d love to write
some material for your blog in exchange for a link back to mine.
Please send me an e-mail if interested. Thank you!
that is a great ideal, we sent you an Email, please feel free to contact us
There is definately a lot to find out about this topic. I like all the points you have
made.
Wow that was strange. I just wrote an very long comment but after I clicked submit my comment didn’t
show up. Grrrr… well I’m not writing all that over again. Anyhow, just wanted
to say excellent blog!
Excellent way of telling, and pleasant post to
take data on the topic of my presentation focus, which i am going to convey in university.
Hey I know this is off topic but I was wondering if you knew of any
widgets I could add to my blog that automatically tweet my newest twitter updates.
I’ve been looking for a plug-in like this for quite some time and was hoping maybe you would
have some experience with something like this.
Please let me know if you run into anything.
I truly enjoy reading your blog and I look forward to your new updates.
Hey there this is kinda of off topic but I was wondering if blogs use WYSIWYG editors or if you have
to manually code with HTML. I’m starting a blog soon but have no coding know-how so I wanted
to get advice from someone with experience. Any help would be enormously appreciated!
This is a topic which is near to my heart… Thank you! Exactly where are your contact details
though?
Thanks for any other informative website.
Where else could I am getting that type of info written in such a perfect means?
I’ve a project that I’m simply now working on, and I have been on the look
out for such information.
at present, we don’t provide any email subscription link or newsletter service, maybe in the future, we will do that, if you really like our website, please feel free to visit firstratemold.com , thanks in advance
I will right away grab your rss feed as I can not to find your email subscription link
or newsletter service. Do you have any? Please permit me
understand in order that I may subscribe. Thanks.