Movable cores and side-actions are commonly used on injection molds to make complex geometries possible. While details are more complicated than described here, some simple calculations provide worst-case estimates for proper sizing.
Force on the Core
Before determining the requirements of the side-action, calculating force on the core is essential. Seal offs, core length and other factors notwithstanding, the designer can simply use maximum projected area and injection pressure to calculate core force.
Maximum Projected Area (C) in square inches is found by sectioning the core at the largest point exposed to plastic.
Maximum Injection Pressure (P) is nozzle pressure in psi (hydraulic ram injection pressure x 10).
Core Force (F) = P x C.
For 20,000 psi and a 2″ dia. pin:
F = (20,000 psi)(3.14 sq.in.) = 62,800 lbs.
Side-Action Options
The following side-action options are possible:
1) Cam Pin with Heel-no preload
2) Cylinder with Heel-no preload
3) Cylinder Only-large
4) Side-Action System-small
While methods 1 and 2 use heel blocks to final position the core, flex and compression is often a problem. More robust preloading methods 3 (with pressure) and 4 (without pressure), eliminate these issues, but require the ability to calculate core and cylinder forces.
Cylinder Basics
Cylinder Push/Extend Force (M) and Cylinder Pull/Retract Force (N) is calculated as follows:
M = H x
N = H x [(3.14xB})/4 – (3.14xR2)/4]
H = Hydraulic supply pressure (psi)
B= Bore diameter of cylinder (in.)
R= Rod diameter of cylinder (in.)
Note for pull, rod area subtracts from the piston area. Retract Force is critical when considering friction from material shrinkage.
Cylinder Sizing
Standard Cylinders: If the machine cylinder hydraulic pressure is known (and available during injection), minimum bore size is:
B = SQRT[(4 x F)/(H x 3.14)]
For 2″ dia. core and H = 1,500 psi:
B = SQRT[(4 x 62,800)/(1,500 x 3.14)]= 7.3 inches (8″ bore cylinder)
Nonstandard Cylinders: Preloading side-action cylinders generate the large output forces of large bore cylinders in a smaller bore package. A typical preload side-action system produces 60,000 lbs of output force with a bore diameter of two inches, and total outside diameter of five inches, easily fitting inside bore of the eight-inch standard cylinder in the example. Nonstandard cylinders may also maintain output force with zero psi hydraulic pressure.
Cylinder calculations provide good first look comparisons when considering the most suitable side-action option early in the mold design.
Hello Dear, are you in fact visiting this site on a
regular basis, if so after that you will without doubt get good know-how.
Hi there, the whole thing is going nicely here and ofcourse every one is sharing data, that’s actually good, keep up writing.
I feel that is one of the so much significant information for me.
And i am satisfied reading your article. But
wanna remark on few general issues, The web site style is perfect, the articles
is actually great : D. Excellent task, cheers
I just couldn’t go away your web site before suggesting that I extremely enjoyed the usual info
a person provide in your guests? Is gonna be back regularly to check up
on new posts
This web site definitely has all the information I wanted about this subject
and didn’t know who to ask.
Hello, I check your blog regularly. Your humoristic style is
witty, keep up the good work!
Hi friends, its wonderful piece of writing regarding educationand fully
defined, keep it up all the time.
I was wondering if you ever thought of changing the page
layout of your site? Its very well written; I love what youve got to
say. But maybe you could a little more in the way of content so people could connect with
it better. Youve got an awful lot of text for only having
one or two pictures. Maybe you could space it out better?
Do you mind if I quote a few of your articles as long as I provide credit and sources back to your webpage?
My blog site is in the exact same area of interest as yours and my users would definitely benefit from some
of the information you provide here. Please let me know if this ok with you.
Appreciate it!
if you would like to read our articles, please feel free to go back to firstratemold.com
Good post. I learn something totally new and challenging
on sites I stumbleupon on a daily basis. It’s always helpful to read through articles from other authors and practice a little something from other web sites.