Movable cores and side-actions are commonly used on injection molds to make complex geometries possible. While details are more complicated than described here, some simple calculations provide worst-case estimates for proper sizing.
Force on the Core
Before determining the requirements of the side-action, calculating force on the core is essential. Seal offs, core length and other factors notwithstanding, the designer can simply use maximum projected area and injection pressure to calculate core force.
Maximum Projected Area (C) in square inches is found by sectioning the core at the largest point exposed to plastic.
Maximum Injection Pressure (P) is nozzle pressure in psi (hydraulic ram injection pressure x 10).
Core Force (F) = P x C.
For 20,000 psi and a 2″ dia. pin:
F = (20,000 psi)(3.14 sq.in.) = 62,800 lbs.
Side-Action Options
The following side-action options are possible:
1) Cam Pin with Heel-no preload
2) Cylinder with Heel-no preload
3) Cylinder Only-large
4) Side-Action System-small
While methods 1 and 2 use heel blocks to final position the core, flex and compression is often a problem. More robust preloading methods 3 (with pressure) and 4 (without pressure), eliminate these issues, but require the ability to calculate core and cylinder forces.
Cylinder Basics
Cylinder Push/Extend Force (M) and Cylinder Pull/Retract Force (N) is calculated as follows:
M = H x
N = H x [(3.14xB})/4 – (3.14xR2)/4]
H = Hydraulic supply pressure (psi)
B= Bore diameter of cylinder (in.)
R= Rod diameter of cylinder (in.)
Note for pull, rod area subtracts from the piston area. Retract Force is critical when considering friction from material shrinkage.
Cylinder Sizing
Standard Cylinders: If the machine cylinder hydraulic pressure is known (and available during injection), minimum bore size is:
B = SQRT[(4 x F)/(H x 3.14)]
For 2″ dia. core and H = 1,500 psi:
B = SQRT[(4 x 62,800)/(1,500 x 3.14)]= 7.3 inches (8″ bore cylinder)
Nonstandard Cylinders: Preloading side-action cylinders generate the large output forces of large bore cylinders in a smaller bore package. A typical preload side-action system produces 60,000 lbs of output force with a bore diameter of two inches, and total outside diameter of five inches, easily fitting inside bore of the eight-inch standard cylinder in the example. Nonstandard cylinders may also maintain output force with zero psi hydraulic pressure.
Cylinder calculations provide good first look comparisons when considering the most suitable side-action option early in the mold design.
We’re a group of volunteers and starting a new scheme in our community.
Your site provided us with valuable information to work on. You have done an impressive job and our whole community will be grateful to you.
This is very interesting, You are a very skilled blogger.
I’ve joined your feed and look forward to seeking more of your great post.
Also, I have shared your website in my social networks!
whoah this weblog is excellent i really like reading your posts.
Keep up the great work! You know, a lot of people are searching
round for this information, you could help them greatly.
Right now it sounds like Expression Engine is the best blogging platform out there right now.
(from what I’ve read) Is that what you’re using on your blog?
maybe you are a professional guy, we want to learn more from you :-)
Good day! This is my first visit to your blog! We are a collection of volunteers and starting a new project
in a community in the same niche. Your blog provided us beneficial information to work on. You have done a outstanding job!
Greetings I am so glad I found your website, I really found you by accident, while I was looking on Digg for something else, Regardless I am here now and would
just like to say kudos for a fantastic post and a all round thrilling
blog (I also love the theme/design), I don’t have time to browse it all at the minute
but I have saved it and also included your RSS feeds, so when I have time I
will be back to read a lot more, Please do keep up
the fantastic work.
I’m extremely impressed with your writing skills and also with the layout on your weblog.
Is this a paid theme or did you customize it yourself? Anyway keep up
the nice quality writing, it’s rare to see a nice blog like this one today.
Fabulous, what a blog it is! This weblog
provides valuable data to us, keep it up.
Good web site you have here.. It’s difficult to find excellent
writing like yours nowadays. I truly appreciate individuals like you!
Take care!!
I am extremely inspired along with your writing
abilities and also with the format on your blog. Is that this a paid topic or did you modify it your self?
Anyway stay up the excellent high quality writing, it’s uncommon to see a great blog
like this one these days..