Movable cores and side-actions are commonly used on injection molds to make complex geometries possible. While details are more complicated than described here, some simple calculations provide worst-case estimates for proper sizing.
Force on the Core
Before determining the requirements of the side-action, calculating force on the core is essential. Seal offs, core length and other factors notwithstanding, the designer can simply use maximum projected area and injection pressure to calculate core force.
Maximum Projected Area (C) in square inches is found by sectioning the core at the largest point exposed to plastic.
Maximum Injection Pressure (P) is nozzle pressure in psi (hydraulic ram injection pressure x 10).
Core Force (F) = P x C.
For 20,000 psi and a 2″ dia. pin:
F = (20,000 psi)(3.14 sq.in.) = 62,800 lbs.
Side-Action Options
The following side-action options are possible:
1) Cam Pin with Heel-no preload
2) Cylinder with Heel-no preload
3) Cylinder Only-large
4) Side-Action System-small
While methods 1 and 2 use heel blocks to final position the core, flex and compression is often a problem. More robust preloading methods 3 (with pressure) and 4 (without pressure), eliminate these issues, but require the ability to calculate core and cylinder forces.
Cylinder Basics
Cylinder Push/Extend Force (M) and Cylinder Pull/Retract Force (N) is calculated as follows:
M = H x
N = H x [(3.14xB})/4 – (3.14xR2)/4]
H = Hydraulic supply pressure (psi)
B= Bore diameter of cylinder (in.)
R= Rod diameter of cylinder (in.)
Note for pull, rod area subtracts from the piston area. Retract Force is critical when considering friction from material shrinkage.
Cylinder Sizing
Standard Cylinders: If the machine cylinder hydraulic pressure is known (and available during injection), minimum bore size is:
B = SQRT[(4 x F)/(H x 3.14)]
For 2″ dia. core and H = 1,500 psi:
B = SQRT[(4 x 62,800)/(1,500 x 3.14)]= 7.3 inches (8″ bore cylinder)
Nonstandard Cylinders: Preloading side-action cylinders generate the large output forces of large bore cylinders in a smaller bore package. A typical preload side-action system produces 60,000 lbs of output force with a bore diameter of two inches, and total outside diameter of five inches, easily fitting inside bore of the eight-inch standard cylinder in the example. Nonstandard cylinders may also maintain output force with zero psi hydraulic pressure.
Cylinder calculations provide good first look comparisons when considering the most suitable side-action option early in the mold design.
Have you ever thought about creating an e-book or guest authoring on other sites?
I have a blog centered on the same subjects you discuss and would really like to
have you share some stories/information. I know my readers would
enjoy your work. If you are even remotely interested,
feel free to shoot me an e mail.
we sent an Email to you, and we are looking forward to your response.
Hi there, You have done a fantastic job. I will definitely digg it and personally
suggest to my friends. I am sure they’ll be benefited from this web site.
hi!,I really like your writing very so much!
percentage we be in contact more about your article on AOL?
I require a specialist in this area to unravel my problem.
May be that is you! Having a look ahead to look you.
Excellent blog post. I certainly appreciate this website.
Keep writing!
I’ve been browsing on-line greater than three hours today, but I never
discovered any fascinating article like yours.
It’s pretty value enough for me. Personally, if all website
owners and bloggers made just right content as
you did, the net can be a lot more useful than ever before.
Hi there everyone, it’s my first pay a quick visit at this web page, and article is truly fruitful
in favor of me, keep up posting these types of content.
Thank you for the good writeup. It in fact was a amusement account it.
Look advanced to far added agreeable from you! By the way,
how can we communicate?
if you have any question or suggestion, please feel free to contact us [email protected]
I am really enjoying the theme/design of your web site.
Do you ever run into any internet browser compatibility issues?
A few of my blog readers have complained about my blog not working correctly in Explorer but looks
great in Chrome. Do you have any suggestions to help fix this issue?
our website is OK! as for your question, I think You can consult to your local professionals
I don’t even understand how I finished up here, however I believed this submit used to be
great. I don’t recognize who you are but definitely you’re
going to a well-known blogger in case you are not already.
Cheers!
For latest news you have to visit web and on internet I found this web site as a most excellent website for newest updates.