Not all problems require the expense and complexity of FEA software. You can calculate many common mold design problems with programs that only require you to enter sizes, forces or other known quantities, including the following:
Reynolds Number to determine if your flow rate is turbulent or laminar. (Turbulent flow is important in cooling because it increases heat transfer. Laminar flow is important for hydraulic systems, so that the oil doesn’t absorb too much heat, which causes the oil viscosity to deteriorate).
Pressure lost through a waterline, bubbler, hose, cooling passage, etc.
How much a leader pin (core pin, ejector pin, etc.) will bend when a load is applied.
The thermal expansion for various materials that go through changes in temperature.
How much a screw, or any item in tension, will stretch.
The gallons per minute of hydraulic oil required to activate a hydraulic cylinder.
The amount a cylinder or cavity will expand due to internal pressure.
How much will a mold plate for a side action mold expand and deform due to molding pressure.
Trigonometric, electrical, production and machining problems and much more
Basically they are the problems that you can solve with a calculator, if you know or have time to find and solve the equations. This type of software organizes what a mold designer might have in his notebook binder and then automates the calculation, which reduces the risk of error.
This software acts like an intelligent calculator to solve deflection and stress in common geometric shapes (e.g., mold plates), long column buckling (e.g., ejector pins), and expansion and compression due to loading. Thermal expansion constants for various materials are available, as well as the ability to calculate the initial size, final size or the total expansion. You also can determine runner and gate sizes and shop calculations, such as effective cutting diameter, trigonometry, tooling ball dimensions, roll dimensions, etc.
These packages are very easy to use and require no training. They eliminate the drudgery and potential for errors, compared with manual calculations.
Simply choose the type of calculation you want, enter the information required and press calculate. The answers appear in a flash. They also can be a great source of reference information, such as hot runner checklists, galvanic tables, screw thread properties, three wire measurements, unit conversions, gate and runner sizes and material properties.
Calculating software is often used to check the output from an FEA package to make certain that the results make sense. For instance, while looking at the results of a cooling analysis it was noticed that there was only one Reynolds Number shown for a water bubbler inside a core pin. It was then asked, “Is that the inside of the bubbler or the outside?”
Using the calculator software, the flow rates shown on the FEA images were used to calculate the Reynolds Number inside the bubbler, calculate the equivalent hydraulic diameter between the bubbler and the drilled hole in the core, and finally the Reynolds Number of the area outside the bubbler.
Whatever your engineering calculation software requirements, choose the option that performs the type of analysis you need. Look at the training required and support needed, then after being shown that the software delivers what you need, use it.
Over-designing your molds is expensive, under-designing is more expensive and often disastrous. Under-design often results in a mold failure, and not all of them are repairable.
Molds are occasionally designed and built where the plates are not strong enough to withstand molding pressure. This is particularly true of “A-side” side-action molds, which results in flashed parting lines. Using the improper sizes for bubblers and holes results in unnecessary pressure losses or poor cooling, and can increase the cycle time.
My brother recommended I might like this blog.
He was once entirely right. This publish
truly made my day. You cann’t consider just how
much time I had spent for this info! Thank you!
Hi! This post couldn’t be written any better! Reading through
this post reminds me of my good old room mate! He always kept chatting
about this. I will forward this page to him. Pretty sure he will have a good read.
Thank you for sharing!
Do you have a spam issue on this blog; I also am a
blogger, and I was wondering your situation; we have developed some nice practices and we are looking to swap methods
with others, please shoot me an email if interested.
until now, we don’t, as for your ideal, if you are really interested in it, please feel free to contact us by Email
When someone writes an post he/she maintains the idea of a user in his/her brain that how a user can know it.
So that’s why this post is outstdanding. Thanks!
I’m no longer positive where you’re getting your info, but great topic.
I needs to spend a while studying much more or working out
more. Thank you for magnificent information I used to be looking for this information for my mission.
Greetings, I believe your blog may be having web browser compatibility issues.
Whenever I look at your blog in Safari, it looks fine however when opening in I.E., it’s
got some overlapping issues. I just wanted to provide you with a quick heads up!
Other than that, excellent site!
please use a higher IE version, that is OK!
I’m not that much of a internet reader to be honest but your blogs really
nice, keep it up! I’ll go ahead and bookmark your site to come back
later. All the best
A motivating discussion is worth comment. I think that you need to publish more on this issue, it may
not be a taboo subject but typically people
don’t talk about these issues. To the next! Many thanks!!
I read this article completely concerning the resemblance of most up-to-date and previous technologies, it’s amazing article.
Good blog you have here.. It’s hard to find high-quality writing
like yours these days. I truly appreciate individuals like you!
Take care!!