Not all problems require the expense and complexity of FEA software. You can calculate many common mold design problems with programs that only require you to enter sizes, forces or other known quantities, including the following:
Reynolds Number to determine if your flow rate is turbulent or laminar. (Turbulent flow is important in cooling because it increases heat transfer. Laminar flow is important for hydraulic systems, so that the oil doesn’t absorb too much heat, which causes the oil viscosity to deteriorate).
Pressure lost through a waterline, bubbler, hose, cooling passage, etc.
How much a leader pin (core pin, ejector pin, etc.) will bend when a load is applied.
The thermal expansion for various materials that go through changes in temperature.
How much a screw, or any item in tension, will stretch.
The gallons per minute of hydraulic oil required to activate a hydraulic cylinder.
The amount a cylinder or cavity will expand due to internal pressure.
How much will a mold plate for a side action mold expand and deform due to molding pressure.
Trigonometric, electrical, production and machining problems and much more
Basically they are the problems that you can solve with a calculator, if you know or have time to find and solve the equations. This type of software organizes what a mold designer might have in his notebook binder and then automates the calculation, which reduces the risk of error.
This software acts like an intelligent calculator to solve deflection and stress in common geometric shapes (e.g., mold plates), long column buckling (e.g., ejector pins), and expansion and compression due to loading. Thermal expansion constants for various materials are available, as well as the ability to calculate the initial size, final size or the total expansion. You also can determine runner and gate sizes and shop calculations, such as effective cutting diameter, trigonometry, tooling ball dimensions, roll dimensions, etc.
These packages are very easy to use and require no training. They eliminate the drudgery and potential for errors, compared with manual calculations.
Simply choose the type of calculation you want, enter the information required and press calculate. The answers appear in a flash. They also can be a great source of reference information, such as hot runner checklists, galvanic tables, screw thread properties, three wire measurements, unit conversions, gate and runner sizes and material properties.
Calculating software is often used to check the output from an FEA package to make certain that the results make sense. For instance, while looking at the results of a cooling analysis it was noticed that there was only one Reynolds Number shown for a water bubbler inside a core pin. It was then asked, “Is that the inside of the bubbler or the outside?”
Using the calculator software, the flow rates shown on the FEA images were used to calculate the Reynolds Number inside the bubbler, calculate the equivalent hydraulic diameter between the bubbler and the drilled hole in the core, and finally the Reynolds Number of the area outside the bubbler.
Whatever your engineering calculation software requirements, choose the option that performs the type of analysis you need. Look at the training required and support needed, then after being shown that the software delivers what you need, use it.
Over-designing your molds is expensive, under-designing is more expensive and often disastrous. Under-design often results in a mold failure, and not all of them are repairable.
Molds are occasionally designed and built where the plates are not strong enough to withstand molding pressure. This is particularly true of “A-side” side-action molds, which results in flashed parting lines. Using the improper sizes for bubblers and holes results in unnecessary pressure losses or poor cooling, and can increase the cycle time.
I was recommended this blog by my cousin. I am not sure whether this post is written by
him as nobody else know such detailed about my difficulty.
You’re incredible! Thanks!
You’ve made some decent points there. I looked on the net to find out more about the issue and found most individuals will go along with your views on this web
site.
My brother recommended I would possibly like this web site.
He was entirely right. This put up actually made my day.
You cann’t consider just how a lot time I had spent for this
information! Thank you!
If you desire to obtain a great deal from this article then you have to apply these techniques to your won website.
I’m really impressed with your writing skills as well
as with the layout on your weblog. Is this a paid theme or did you customize it yourself?
Anyway keep up the excellent quality writing, it’s
rare to see a great blog like this one nowadays.
actually it is First-rate Mold Solution Co., Ltd. Team to manage firstratemold.com
Magnificent goods from you, man. I have understand your stuff previous to and you are
just extremely wonderful. I really like what you’ve acquired here, really like what you’re saying and the way in which you say it.
You make it entertaining and you still take care of to keep it smart.
I can’t wait to read far more from you. This is really a wonderful web site.
We absolutely love your blog and find many of your post’s to be what precisely I’m looking for.
can you offer guest writers to write content available for you?
I wouldn’t mind publishing a post or elaborating on a few of the subjects you write about here.
Again, awesome site!
These are actually fantastic ideas in concerning blogging.
You have touched some fastidious points here. Any way keep up wrinting.
I pay a visit each day some websites and websites to read content, but this weblog offers feature based posts.
Fastidious answers in return of this difficulty with real arguments and
telling all concerning that.