Not all problems require the expense and complexity of FEA software. You can calculate many common mold design problems with programs that only require you to enter sizes, forces or other known quantities, including the following:
Reynolds Number to determine if your flow rate is turbulent or laminar. (Turbulent flow is important in cooling because it increases heat transfer. Laminar flow is important for hydraulic systems, so that the oil doesn’t absorb too much heat, which causes the oil viscosity to deteriorate).
Pressure lost through a waterline, bubbler, hose, cooling passage, etc.
How much a leader pin (core pin, ejector pin, etc.) will bend when a load is applied.
The thermal expansion for various materials that go through changes in temperature.
How much a screw, or any item in tension, will stretch.
The gallons per minute of hydraulic oil required to activate a hydraulic cylinder.
The amount a cylinder or cavity will expand due to internal pressure.
How much will a mold plate for a side action mold expand and deform due to molding pressure.
Trigonometric, electrical, production and machining problems and much more
Basically they are the problems that you can solve with a calculator, if you know or have time to find and solve the equations. This type of software organizes what a mold designer might have in his notebook binder and then automates the calculation, which reduces the risk of error.
This software acts like an intelligent calculator to solve deflection and stress in common geometric shapes (e.g., mold plates), long column buckling (e.g., ejector pins), and expansion and compression due to loading. Thermal expansion constants for various materials are available, as well as the ability to calculate the initial size, final size or the total expansion. You also can determine runner and gate sizes and shop calculations, such as effective cutting diameter, trigonometry, tooling ball dimensions, roll dimensions, etc.
These packages are very easy to use and require no training. They eliminate the drudgery and potential for errors, compared with manual calculations.
Simply choose the type of calculation you want, enter the information required and press calculate. The answers appear in a flash. They also can be a great source of reference information, such as hot runner checklists, galvanic tables, screw thread properties, three wire measurements, unit conversions, gate and runner sizes and material properties.
Calculating software is often used to check the output from an FEA package to make certain that the results make sense. For instance, while looking at the results of a cooling analysis it was noticed that there was only one Reynolds Number shown for a water bubbler inside a core pin. It was then asked, “Is that the inside of the bubbler or the outside?”
Using the calculator software, the flow rates shown on the FEA images were used to calculate the Reynolds Number inside the bubbler, calculate the equivalent hydraulic diameter between the bubbler and the drilled hole in the core, and finally the Reynolds Number of the area outside the bubbler.
Whatever your engineering calculation software requirements, choose the option that performs the type of analysis you need. Look at the training required and support needed, then after being shown that the software delivers what you need, use it.
Over-designing your molds is expensive, under-designing is more expensive and often disastrous. Under-design often results in a mold failure, and not all of them are repairable.
Molds are occasionally designed and built where the plates are not strong enough to withstand molding pressure. This is particularly true of “A-side” side-action molds, which results in flashed parting lines. Using the improper sizes for bubblers and holes results in unnecessary pressure losses or poor cooling, and can increase the cycle time.
Hey there! Someone in my Myspace group shared this website with
us so I came to take a look. I’m definitely enjoying the information. I’m book-marking and will be tweeting this to my followers!
Great blog and great style and design.
Hi, I do believe this is an excellent blog. I stumbledupon it ;) I’m going to revisit yet
again since I book-marked it. Money and freedom is the best
way to change, may you be rich and continue to guide other people.
I go to see daily some web sites and websites to read posts,
except this website offers feature based content.
Hmm it seems like your website ate my first comment (it was super long) so I guess I’ll just sum it up what I wrote and say, I’m thoroughly enjoying your
blog. I as well am an aspiring blog writer but I’m
still new to everything. Do you have any recommendations for
newbie blog writers? I’d definitely appreciate it.
I’m really enjoying the design and layout of your blog.
It’s a very easy on the eyes which makes it much more
enjoyable for me to come here and visit more often. Did you hire out a designer to create
your theme? Excellent work!
Write more, thats all I have to say. Literally, it seems as though you relied on the video to make your point.
You clearly know what youre talking about, why waste your intelligence on just posting
videos to your blog when you could be giving us something enlightening to read?
your ideal is great!
Hello, i think that i saw you visited my web site thus i came to “return the
favor”.I am attempting to find things to improve
my web site!I suppose its ok to use some of your ideas!!
Hi there, I would like to subscribe for this website to take hottest updates,
thus where can i do it please help.
until now, one thing you can do is to come back to firstratemold.com to read hottest updates
Hi to every one, it’s actually a pleasant for me to pay
a visit this web site, it consists of useful Information.
If some one desires to be updated with latest technologies
therefore he must be pay a quick visit this website and be up to date every day.