High-speed machining (HSM) is usually associated with high-speed spindles (15K to 40K rpm) and higher feedrates. It is also referred to as high velocity machining. They are one in the same, as both represent machining components in the most accurate and shortest cycle times.

In the past 10 to 15 years HSM was focused on the mold and die industry that uses pre-hardened materials and hardened tool steels—such as P-20, H-13, S-7 and D-2, which range in hardness from 28-62 HRC. The traditional method of finish machining hardened materials was EDM. In applications where HSM can replace the EDM process there will be considerable cost and cycle time reductions.

To be successful with HSM the following components need to be integrated; if one of these is incorrectly applied then your machining application will suffer.

Not everyone understands how and when to apply the correct HSM principles. This is not to say that every machining application will benefit from HSM, but many applications could if it weren’t for misinformation and assumptions.

This is the most significant component for HSM, and should be designed specifically for HSM. The construction of the base, as well as the individual components—drive train, spindle and CNC—must be capable of handling the demands of HSM, especially in the case of hard milling.

It is much more than just looking at the maximum spindle rpm and feedrates. You must consider the size and mix of work to be machined. Know what you are planning to machine and evaluate accordingly. Are you going to be machining 2-D or 3-D surfaces on components or are materials to be machined, soft or hardened? These are just two examples.

A machine is purchased with the highest spindle rpm available: 40K with 1,000 ipm feedrate. Sounds great, right? Let’s go further: all of your parts are very intricate and small, you have some of the best HSM cutting tools (1.0mm in Dia. / 2-Flute) designed for 60K rpm with a chip load of .003″. Now you are limited by the 40K spindle, so you will have to run cutters at a reduced rpm of 40K. Calculate the feedrate (40K x 2x.003″) and you have 240 ipm feedrate. Now we have 40K rpm and 240 ipm, so we’re really moving!

Wait, remember the size and intricacy of the parts you will be running? What if you cannot reach the 240 ipm because of the part configuration? You must slow down the spindle speed to maintain the chip load of .003″ due to the actual feedrate that can be attained when actually cutting. The point is, you can only go as fast as the slowest link will allow (machine, CNC control, toolholder, cutting tools).

There is no one toolholder type that will satisfy all applications: shrink fit, hydraulic, collet style, etc. They all have specific features that can be applied depending upon the application. The same goes for the spindle taper interface as there are specific features for HSK and CAT, which are inherently different. These need to be evaluated depending upon your machining requirements.

Balancing is very important, but not all tools need to be balanced! It depends on what is required of the toolholder. Balance considerations start at about 8K rpm. That does not mean you balance all toolholders that will be run at 8K, it means that is where you start to think about balancing.

For instance, if a tool is to be run at 9K rpm and used in a roughing application it very well may not need to be balanced. On the other hand, toolholders that will be used for finishing operations at speeds above 8K rpm may benefit from balancing. It all depends upon your requirements.

This is one area where companies try to cut corners because of the cost associated per piece, but there are more variables to consider—performance and better finishes, along with how long the tool will perform well in the cut. In some cases, you can throw commodity-type tools at an application, but you will have shorter and less consistent tool life, resulting in more downtime changing tools, etc. You need to know what is expected of the cutting tool—surface finish, material hardness and tool life requirements—so you can run lights out, unattended.

CAD/CAM Systems
There are still many CAD/CAM systems that do not have the capabilities to create toolpaths for HSM or hard milling routines easily. To be able to evaluate a system, you must understand what types of routines are required for HSM to attain the best results. Using experts in the field will reduce your learning curve considerably.

About First-rate Mold Solution Co., Ltd.
First-rate Mold Solution Co., Ltd. in China, provide industry design,mold design,mold manufacturing,molding analysis,project management service.

About firstratemold.com
our website has a lot of professional knowledges in mold industry in blog and news, also we are interested in CAD/CAM/CAE, such as AUTOCAD,UGNX, PRO/E,CATIA, CIMATRON, SOLIDWORKS, MOLDFLOW and so on,we welcome professional engineer,mold maker and someone who are interested in injection molding,plastic product,injection mold and mold industry to our section of blog and news,we would like to share with them