There are many different variations of extrusion equipment. They vary by four major characteristics:
Movement of the extrusion with relation to the ram. If the die is held stationary and the ram moves towards it then its called “direct extrusion”. If the ram is held stationary and the die moves towards the ram its called “indirect extrusion”.
The position of the press, either vertical or horizontal.
The type of drive, either hydraulic or mechanical.
The type of load applied, either conventional (variable) or hydrostatic.
A single or twin screw auger, powered by an electric motor, or a ram, driven by hydraulic pressure (often used for steel and titanium alloys), oil pressure (for aluminum), or in other specialized processes such as rollers inside a perforated drum for the production of many simultaneous streams of material.Typical extrusion presses cost more than $100,000, whereas dies can cost up to $2000.
Forming internal cavities
There are several methods for forming internal cavities in extrusions. One way is to use a hollow billet and then use a fixed or floating mandrel. A fixed mandrel, also known as a German type, means it is integrated into the dummy block and stem. A floating mandrel, also known as a French type, floats in slots in the dummy block and aligns itself in the die when extruding. If a solid billet is used as the feed material then it must first be pierced by the mandrel before extruding through the die.
A special press is used in order to control the mandrel independently from the ram. The solid billet could also be used with a spider die, porthole die or bridge die. All of these types of dies incorporate the mandrel in the die and have “legs” that hold the mandrel in place. During extrusion the metal divides and flows around the legs, leaving weld lines in the final product.
Direct extrusion
Direct extrusion, also known as forward extrusion, is the most common extrusion process. It works by placing the billet in a heavy walled container. The billet is pushed through the die by a ram or screw. There is a reusable dummy block between the ram and the billet to keep them separated. The major disadvantage of this process is that the force required to extrude the billet is greater than that need in the indirect extrusion process because of the frictional forces introduced by the need for the billet to travel the entire length of the container.
Because of this the greatest force required is at the beginning of process and slowly decreases as the billet is used up. At the end of the billet the force greatly increases because the billet is thin and the material must flow radially to exit the die. The end of the billet, called the butt end, is not used for this reason.
Indirect extrusion
In indirect extrusion, also known as backwards extrusion, the billet and container move together while the die is stationary. The die is held in place by a “stem” which has to be longer than the container length. The maximum length of the extrusion is ultimately dictated by the column strength of the stem. Because the billet moves with the container the frictional forces are eliminated. This leads to the following advantages:
A 25 to 30% reduction of friction, which allows for extruding larger billets, increasing speed, and an increased ability to extrude smaller cross-sections
There is less of a tendency for extrusions to crack because there is no heat formed from friction
The container liner will last longer due to less wear
The billet is used more uniformly so extrusion defects and coarse grained peripherals zones are less likely.
The disadvantages are:
Impurities and defects on the surface of the billet affect the surface of the extrusion. These defects ruin the piece if it needs to be anodized or the aesthetics are important. In order to get around this the billets may be wire brushed, machined or chemically cleaned before being used.
This process isn’t as versatile as direct extrusions because the cross-sectional area is limited by the maximum size of the stem.
Hydrostatic extrusion
In the hydrostatic extrusion process the billet is completely surrounded by a pressurized liquid, except where the billet contacts the die. This process can be done hot, warm, or cold, however the temperature is limited by the stability of the fluid used. The process must be carried out in a sealed cylinder to contain the hydrostatic medium. The fluid can be pressurized two ways:
Constant-rate extrusion: A ram or plunger is used to pressurize the fluid inside the container.
Constant-pressure extrusion: A pump is used, possibly with a pressure intensifier, to pressurize the fluid, which is then pumped to the container.
The advantages of this process include:
No friction between the container and the billet reduces force requirements. This ultimately allows for faster speeds, higher reduction ratios, and lower billet temperatures.
Usually the ductility of the material increases when high pressures are applied.
An even flow of material.
Large billets and large cross-sections can be extruded.
No billet residue is left on the container walls.
The disadvantages are:
The billets must be prepared by tapering one end to match the die entry angle. This is needed to form a seal at the beginning of the cycle. Usually the entire billet needs to be machined to remove any surface defects.
Containing the fluid under high pressures can be difficult.
Drives
Most modern direct or indirect extrusion presses are hydraulically driven, but there are some small mechanical presses still used. Of the hydraulic presses there are two types: direct-drive oil presses and accumulator water drives.
Direct-drive oil presses are the most common because they are reliable and robust. They can deliver over 35 MPa (5000 psi). They supply a constant pressure throughout the whole billet. The disadvantage is that they are slow, between 50 and 200 mm/s (2–8 ips).
Accumulator water drives are more expensive and larger than direct-drive oil presses, plus they lose about 10% of their pressure over the stroke, but they are much faster, up to 380 mm/s (15 ips). Because of this they are used when extruding steel. They are also used on materials that must be heated to very hot temperatures for safety reasons.Hydrostatic extrusion presses usually use castor oil at pressure up to 1400 MPa (200 ksi). Castor oil is used because it has good lubricity and high pressure properties.
Extrusion defects
Surface cracking – When the surface of an extrusion splits. This is often caused by the extrusion temperature, friction, or speed being too high. It can also happen at lower temperatures if the extruded product temporarily sticks to the die.
Pipe – A flow pattern that draws the surface oxides and impurities to the center of the product. Such a pattern is often caused by high friction or cooling of the outer regions of the billet.
Internal cracking – When the center of the extrusion develops cracks or voids. These cracks are attributed to a state of hydrostatic tensile stress at the centerline in the deformation zone in the die. (A similar situation to the necked region in a tensile stress specimen)
An extrusion machine consist of various component for the various stage of the extrusion process. The entire process can be fully automated. Plastic can be extruded in the continuous and semi-continuous manner and in various shapes like round, rectangular, tubes etc. The resin that is introduced into the machine, get melted and eventually forced out through the die. The design of the die decides the ultimate shape of the product. Plastic solidifies on cooling. After which the plaster is cut in section according to the required size.
Types of extrusion machines: Basically, an extruder machine consist of a feed screw, barrel and temperature controller. But the design and features of the machine depend of several other factors like the type of material to be extruded and the design of the product. A profusion of plastic extrusion machines are available in the market, some of them being:
HDPE pipe Extrusion line
Plastic Sheet Extrusion Machine
Blown Film Plant
PP TQ Film Plant
Multi layer Blown Film Plant
Cast Film Line
Raffia Tape Stretching Line
Plastic Extrusion MachinesAir Bubble Sheet Plant
PP/HDPE Box Strapping Plant
PET Box Strapping Plant
Extrusion Coating Lamination Plant
PP/HDPE/PET Monofilament plant
Synthetic String Plant (Sutli Plant)
PET Recycling Plant
HDPE/RPVC/PPR Pipe Plant
Features of machines
Plastic extrusion machines can be either standardized or custom made. In either of the case some of the feature of the machines are to paid special attention so as to get optimum productivity and quality.
Application
The application of plastic is highly relevant both in industrial, commercial and domestic sector. Some of the commonly used plastic extruded products are release paper, soft food packaging, medical packaging, paper packaging, industrial packaging, pipe, blown film, coated paper, plastic filaments for brush bristles, carpet fibers, vinyl siding, and many more.
Extrusion processes can vary significantly depending on the specific requirements of the desired product and the materials being used. Understanding the different types of extrusion processes is essential for selecting the most suitable method for a given application.
Continuous vs. Batch Extrusion
Continuous Extrusion: In continuous extrusion, the raw material is continuously fed into the extruder machine, and the extruded product is continuously formed and cut to the desired length. This method is ideal for high-volume production of uniform products such as pipes, tubes, and profiles.
Batch Extrusion: Batch extrusion involves processing a finite quantity of material within the extruder machine, typically in discrete batches. Once a batch is completed, the extruder is stopped, and the product is removed before starting the next batch. Batch extrusion is often used for smaller-scale production runs or when frequent material changes are required.
Direct vs. Indirect Extrusion
Direct Extrusion: In direct extrusion, the material is pushed through the die directly by the motion of the extruder screw. This process is characterized by high productivity and efficiency, making it suitable for a wide range of applications in industries such as plastics, metals, and food processing.
Indirect Extrusion: Indirect extrusion involves pushing the material through the die using a moving container or “dummy block” positioned behind the die. This method offers greater control over the extrusion process and can be used to produce intricate shapes and profiles with improved surface finish and dimensional accuracy.
Extrusion molding is a high-volume manufacturing process used to create objects with a fixed cross-sectional profile. It is a molding process that involves forcing a material, typically a thermoplastic or elastomer, through a shaped opening or die to produce a continuous length of the desired shape, which is typically tube- or rod-like. The material is heated until it becomes pliable or molten, and then it is forced through the die to create the desired cross-sectional profile. Besides using this method to shape plastic, it is also used on metals.