Drawing is a metalworking process which uses tensile forces to stretch metal. It is broken up into two types: sheet metal drawing and wire, bar, and tube drawing.
The specific definition for sheet metal drawing is that it involves plastic deformation over a curved axis. For wire, bar, and, tube drawing the starting stock is drawn through a die to reduce its diameter and increase its length. Drawing is usually done at room temperature, thus classified a cold working process, however it may be performed at elevated temperatures to hot work large wires, rods or hollow sections in order to reduce forces.
Sheet metal
The success of forming is in relation to two things, the flow and stretch of material. As a die forms a shape from a flat sheet of metal, there is a need for the material to move into the shape of the die. The flow of material is controlled through pressure applied to the blank and lubrication applied to the die or the blank.
If the form moves too easily, wrinkles will occur in the part. To correct this, more pressure or less lubrication is applied to the blank to limit the flow of material and cause the material to stretch or thin. If too much pressure is applied, the part will become too thin and break. Drawing metal is the science of finding the correct balance between wrinkles and breaking to achieve a successful part.
Deep drawing
Drawing can also be used to pull metal over a die (male mold) to create a specific shape. For example, stainless steel kitchen sinks are formed by drawing the stainless steel sheet metal stock over a form (the die) in the shape of the sink. Beverage cans are formed by drawing aluminium stock over can-shaped dies. By comparison, hydroforming forces metal into a female mold using pressure.
Bar, tube & wire
Bar, tube, and wire drawing all work upon the same principle: the starting stock drawn through a die to reduce the diameter and increase the length. Usually the die is mounted on a draw bench. The end of the workpiece is reduced or pointed to get the end through the die. The end is then placed in grips and the rest of the workpiece is pulled through the die. Steels, copper alloys, and aluminium alloys are common materials that are drawn.
Drawing can also be used to produce a cold formed shaped cross-section. Cold drawn cross-sections are more precise and have a better surface finish than hot extruded parts. Inexpensive materials can be used instead of expensive alloys for strength requirements, due to work hardening.
Bar drawing
Bars or rods that are drawn cannot be coiled therefore straight-pull draw benches are used. Chain drives are used to draw workpieces up to 30 m (98 ft). Hydraulic cylinders are used for shorter length workpieces.
The reduction in area is usually restricted to 20 to 50%, because greater reductions would exceed the tensile strength of the material, depending on its ductility. To achieve a certain size or shape multiple passes through progressively smaller dies or intermediate anneals may be required.
Tube drawing
Tube drawing is very similar to bar drawing, except the beginning stock is a tube. It is used to decrease the diameter, improve surface finish and improve dimensional accuracy. A mandrel may or may not be used depending on the specific process used.
Wire drawing
This technique has long been used to produce flexible metal wire by drawing the material through a series of dies of decreasing size. These dies are manufactured from a number of materials, the most common being tungsten carbide and diamond.
Plastic drawing
Plastic drawing, sometimes referred to as cold drawing, is the same process as used on metal bars, but applied to plastics.
Cold drawing is primarily used in manufacturing plastic fibers. The process was discovered by Julian Hill in 1930 while trying to make fibers from an early polyester.
It is performed after the material has been “spun” into filaments; by extruding the polymer melt through pores of a spinneret. During this process, the individual polymer chains tend to somewhat align because of viscous flow. These filaments still have an amorphous structure, so they are drawn to align the fibers further, thus increasing crystallinity, tensile strength and stiffness. This is done on a draw twister machine.
For nylon, the fiber is stretched four times its spun length. The crystals formed during drawing are held together by hydrogen bonds between the amide hydrogens of one chain and the carbonyl oxygens of another chain.
Drawing is a manufacturing process that uses tensile forces to elongate metal, glass, or plastic. As the material is drawn (pulled), it stretches and becomes thinner, achieving a desired shape and thickness. Drawing is classified into two types: sheet metal drawing and wire, bar, and tube drawing. Sheet metal drawing is defined as a plastic deformation over a curved axis. For wire, bar, and tube drawing, the starting stock is drawn through a die to reduce its diameter and increase its length. Drawing is usually performed at room temperature, thus classified as a cold working process; however, drawing may also be performed at higher temperatures to hot work large wires, rods, or hollow tubes in order to reduce forces.
Drawing is a metalworking process which uses tensile forces to stretch metal. It is broken up into two types: sheet metal drawing and steel tube drawing. The specific definition for sheet metal drawing is that it involves plastic deformation over a curved axis. For wire, bar, and tube drawing the starting stock is drawn through a dye to reduce its diameter and increase its length.
The drawing off steel tubing is usually done at room temperature, thus classified as a cold working process. It may however be performed at elevated temperatures to hot work large wires, rods or hollow sections in order to reduce forces.
Bar, tube and wire drawing all work upon the same principle: the starting stock drawn through a die to reduce the diameter and increase the length. Usually the die is mounted on a draw bench. The end of the steel tube is reduced or pointed to get the end through the die. Steels, copper alloys, and aluminium alloys are common materials that are drawn. Die picture below depicts the drawing process of a steel tube.
With tube drawing, the beginning stock is a steel tube. It is used to decrease the diameter, improve surface finish and improve dimensional accuracy. A mandrel may or may not be used depending on the specific process used. The process of plug drawing can be applied if the inside diameter (id) of the steel tube needs to be controlled. A tool is then manufactured which allows the steel tube to be drawn down to the required size while ensuring that the inside diameter of the steel tube is as close as possible to the pre-set tolerance given.
Tubecon can draw or plug draw steel tubes according to customer specification. Not only does Tubecon use the drawing process for precision tubes as welded steel profiles can also be manufactured using the drawing process. For smaller quantities steel sections that are not specified as standard drawing can be a great advantage to the end consumer.
The process of drawing can take a round steel tube, called the mother tube, to a square, rectangle or profile as the end result.