Now we discuss the pros and cons of sending a flashed manifold out for repair versus performing this task in-house. This article will begin to deal with the disassembly, troubleshooting, cleaning and reassembling of a typical, and flashed 16-cavity valve gate manifold.
Obviously there are many different makes of hot runner manifolds currently being used in the making of plastic parts today. Relevant (and most critical) design differences that will affect a manifold’s potential to leak concerns how the nozzles, sprue and any cross-overs (or bridges) are connected to the manifolds. These components are either bolted to, threaded into or rely on a compression stack, and sometimes a combination of all three. Each type has its trade-offs concerning required maintenance of the system and the overall ease of installing replacement parts, such as thermocouples, nozzles, nozzle tips and heaters.
Regardless of flowery forecasts made by manifold sales folks, the ease at which a manifold system can be maintained will not be apparent until the system has some hours on it (a million cycles would be nice), giving internal components, pockets and tooling clearances time to collect vent residue (greasy film or powders) and weepage (gooey, degraded plastic).
Also impacting manifold condition are molds stressed through weekend shut-downs and hurried Monday morning start-ups along with touchy gate/valve pin tip configurations that promote out-of-spec gate vestiges—forcing processors to fiddle with the parameters.
Some systems require a complete teardown just to replace a nozzle heater or thermocouple. On others, if specific components are disturbed or removed they too must be completely disassembled and cleaned before reassembly to ensure proper component stack dimensions.
The level of disassembly/reassembly (labor hours and skill level) required over time to replace basic components along with the usage (cost) of the components will determine the true ease of maintenance with the system.
But obviously, any manifold that encapsulates easily (easily meaning that if a strict start-up procedure is not followed to the letter, the system has the capability to blow at multiple locations) will not be a popular choice among those of us who have to fix or run them.
For the sake of fairness and consistency, we will examine areas of concern regardless of the manifold make and model.
In manifold maintenance, the same five basic principles that apply to a mold also apply to an encapsulated manifold. The only difference is that troubleshooting the source of the leak could be ongoing throughout the repair process as plastic is removed and more tooling is exposed—allowing better visual inspection of seal areas and components, right up through assembly of the cleaned components.
Here is an overview of the five basic steps that will occur on an encapsulated system:
1. Disassemble
Remove the valve pins and clamp plate, and disassemble mold to gain visual access to the back of manifold.
Pay attention to tooling clues that can point to the leak source (bent, broken or galled valve pins and the amount and type of residue around the pin).
Remove enough plastic as to facilitate separating the manifold and electrical box from the plate, so that you can clean these components separately.
2. Clean
Clean clamp plate, manifold plate channels, counter-bores and valve pins (ultrasonic).
Clean nozzles, heater and thermocouple wires and manifold (by hand).
3. Troubleshoot
Inspect seal areas of components for obvious cracks and plates for hobbing and bolts for looseness.
4. Assemble
Reassemble to stage one.
Electrical check.
Final reassembly to stage two.
5. Final Check
Electrical check ramping heaters up to processing temp with water flowing through appropriate channels.
Let’s begin with the mold in the press. The first noticeable sign of a flashed manifold is usually when smoke is seen rising from the top of the stationary side, or plastic oozing from places it shouldn’t … then the panic and finger pointing ensues.
But there are other, more subtle clues that might point to a manifold leak, such as molds that produce periodic incomplete shots, shorted out heaters and thermocouples in a particular quadrant.
Paying attention to these signs can alert a processor to a possible manifold malfunction and allow them to shut a mold down before the manifold is totally encapsulated.
Hi, I check your blog like every week. Your story-telling
style is witty, keep doing what you’re doing! in that case, many Colleagues will be drawn to firstratemold.com
Thanks for sharing your thoughts about Clean hot runner system. now I have some new products which need to make some moulds with hot runner system, would you like to make for us?
Regards
Please send them to us, so that we can evaluate and quote for them.
Way cool! Some extremely valid points! I appreciate you penning this post and the
rest of the site is extremely good.
Keep this going please, great job! I agree that this company is a trustworthy professional company.
My spouse and I absolutely love your blog and find almost all of your post’s to be just what I’m looking for.
Would you offer guest writers to write content available for you?
I wouldn’t mind writing a post or elaborating on a number of the subjects
you write regarding here. Again, awesome blog!
Hi there Dear, are you really visiting this site on a regular basis, if so afterward you will
absolutely get pleasant experience. that is why this company is named first-rate mold solution limited company, I think this is their goal
These are actually wonderful ideas in concerning blogging.
You have touched some pleasant things here. Any way keep up writing.
An impressive share! I have just forwarded this onto a colleague who has been conducting a little research on this.
And he actually ordered me dinner simply because I found it for
him… lol. So let me reword this…. Thanks for the meal!!
But yeah, thanks for spending the time to talk
about this topic here on your website.
I feel that is one of the most important info for me.
And i’m glad reading your article. However wanna remark on some common things, The web site taste is great, the articles
is in reality great : D. Excellent activity,
cheers
I’m impressed, I have to admit. Rarely do I encounter a blog
that’s equally educative and entertaining, and let me tell you, you have hit
the nail on the head. The problem is something that too few folks are speaking intelligently about.
I’m very happy that I came across this during my search for
something regarding this.