Now we have understood the importance of mold design review, do you know how to start? Generally, The mold designer then uses the information gathered for him from the previous steps to generate a mold design and submit a tool assembly drawing to the mold buyer for approval.

The next step is mold design review, which ensures that the mold will meet specified requirements and comply with proven industry best practices. Despite pressure to complete this step as fast as possible, conducting a poor mold design review is not cost-effective. As the mold progresses through the manufacturing process, the cost of correcting errors climbs rapidly. Instead of rushing, consider each of the following factors during your next mold design review:

Structural integrity. Is the mold appropriately designed to withstand the forces it will encounter in handling and operation? Consider general alignment from pillars and bushings, not just the fixed and moving halves, but also any moving elements. Is the proposed guidance sufficient to ensure proper alignment and long life? Are the bearing elements accessible for mold maintenance? Are proper straps and lifting points for safe handling included in the design?

Mold splitting and alignment control. For many molds, wear at the split lines greatly influences mold life and part quality, so accurate control of the split lines during final closing is crucial. On the main mold halves, alignment locks are an effective way to ensure consistent mold closing. Locks need to follow manufacturers’ recommendations for loading and should be incorporated into the mold to minimize thermal expansion effects.

A good mold design review considers the alignment of all moving cavity-forming sections. Side cores and rising cores must be designed to consistently and accurately locate when the mold is new and as the mold wears. To accurately predict which surfaces will wear and how that wear will impact the moving mold element location, assess how well the element is guided and located in its closed position. It is also important to consider the influence of melt pressure. Too often, a rising core does not make a hard stop and an undercut feature moves in position, depending on the molding conditions. Alignment issues rarely crop up when the mold is new, but, as the cycle count goes up, problems creep in.

Gating/runner system. Ensure that the gating solution implemented in the mold design is consistent with what was used in the simulation. The most common problem that is identified in troubleshooting a mold is that its actual performance does not match what was predicted in the simulation. The first element to check is gate size. It is surprising how often the gating specified in the mold design does not match what was used in simulation. Other factors to consider include the gate scar blemish (again, this should be considered in the DFM phase), and the ejection or separation of the runner system.

Venting. A common approach to venting is “venting equals metal off,” whereby the mold is built and the venting is added after trialing. This is a lost opportunity. Simulation should show where specific venting is required, which should then propel venting to be incorporated at the design stage. Selecting appropriate vent size is based on understanding the smallest gap into which the chosen resin will flash. So, as part of the mold design review, verify that all shut-off faces are vented, that all end of fills are properly vented and that each venting solution can be adequately cleaned. Ideally, vents will be self-cleaning by the actions of the components as the mold operates.

Cooling/temperature control. Local hot or cold spots do not yield a stable processing window for mold optimization. For small, complex tools with rising cores and ejectors, the challenge is to get the cooling close enough to the part-forming surfaces. Many techniques and products are available to facilitate thermal mold management. New technologies enable complex conformal cooling circuits to be added, for example, but care must be taken not to sacrifice channel diameter for the perfect channel location. Oftentimes, a compromise must be made to ensure a sufficient flow rate for removal of the required amount of heat from the tool. A mold design review can identify the presence of cooling, then determine if that cooling is sufficient for keeping the entire mold at an appropriate processing temperature. It also can ensure that the cooling channel locations do not impact the tool’s robustness by intersecting other features.

Another thermal management consideration is differential thermal expansion, whereby different elements of the tool structure expand at different rates as the tool heats up. This can cause bearing wear due to the varying temperatures between a mold’s plates. To ensure proper cooling, it is now possible to simulate the thermal profile of the mold design, and consider all materials and cooling channels to yield a precise prediction of mold temperatures and how they will differ across the core and cavity.

De-molding/ejection. The sequence of mold opening and part removal needs to occur as efficiently as possible. The ejection solution must ensure that no unwanted marks are created on critical surfaces. This should have been identified at the mold specification phase. Any undercut features also need to be cleared as part of the de-molding sequence. The actual mechanisms for de-molding may be driven by mold opening and plate movements and can reduce the risk of damage during production. Alternatively, externally powered actuators operating in a specific sequence need to be carefully controlled to avoid collisions that can cause costly tool damage.

The mold design review must assess each moving mold element for location repeatability, risk of damage during operation and maintainability. It can achieve this assessment by working through the de-molding sequence and ensuring that the undercuts release in the correct order and do not pull the part to one side as the final ejection stroke occurs.

Materials. Typically, mold materials are detailed in the tooling specification. The reviewer of the mold design must ensure that the correct materials have been specified (in proper metallurgical condition from heat-treatment) and that mating materials forming a sliding pair are not the same and/or have different hardness levels.

Finishes/coatings. Any special finishes and coatings should also be defined in the mold specification. Finishes include textures or patterns that will leave an imprint on the molded part’s surface. Coatings reduce wear either at the bearing surface or on the cavity surface. The mold design reviewer must ensure that the specification has been correctly interpreted in the tool.

Each of the aspects of mold design review presented here is essential to ensure that a robust mold will be produced that can support the process capability of the part design and provide long, trouble-free performance.