Mold building in China is a very challenging business. Two of the difficulties are offshore competition and molders’ growing demands for early design involvement. One solution to combat these challenges is mold filling simulation. Its use can help mold builders stay competitive, enhance efficiencies, meet customer expectations and create more business opportunities. Following are four main benefits of today’s mold simulation tools.
A 3D tool improves prediction of melt filling and air venting behavior. Mold failures during tool trials can cause a lack of confidence in a mold builder’s reputation as well as lost revenue.
Plastics flow behavior involves a combination of flow, pressure, cooling and heat. When you alter any influence on this complex combination (for example, part geometry, runner system or cooling system), the molding behavior may change. The gates must be placed at the most appropriate and feasible locations to allow enough melted plastic to fill and pack/hold into the cavity.
Mold filling simulation now provides a 3D-solver-based, scientific approach to determine the proper gating strategy and venting arrangement based on the predicted melt front. Simulation tools provide a series of features that enable mold designers to evaluate cold/hot runner scenarios with a
built-in template of gate/runner types. In facilitating such features, flow analysis predicts the required injection pressure and further estimates the required press size range.
Venting is always another major concern for mold builders. With the flow front analysis, air traps can be predicted and displayed in a 3D model. When air traps occur on a non-parting surface, they can be minimally improved by changing either the gate or the part thickness. When air traps occur on a parting surface, virtual vents can be set in the simulation tool to evaluate any improvement. 3D simulation tools using highly accurate theory will effectively avoid the risk of re-tooling and multiple tryouts.
The ability to evaluate different cooling arrangements can deliver more accurate cycle time estimation. Cycle time is always critical to OEMs and molders for meeting expected productivity levels. Without simulation, cycle time is estimated based on thickness distribution or past experience with similar part geometries. However, this estimation does not take into account cooling time for hot spots/undercuts or the potential cooling circuit efficiency.
With modern 3D mold filling simulation software, it’s feasible to evaluate different cooling arrangements by comparing accurate cycle time based on the whole system, efficiency of each cooling loop, adequate cooling channel size and plastic frozen percentage.
An optimized cooling system will help to facilitate an improvement in mold temperature control, which helps to maintain a minimum cycle time. Cooling analysis also helps maintain part shrink and deflection, which can occur as a result of mold temperature differences between the core and cavity sides.
Mold design enhancements in relation to cooling will save customers significant time and effort down the road.
Integration with 3D CAD/CAM can boost efficiency. Many mold designers design molds only in their familiar CAD/CAM software and outsource the molding simulation, and this requires massive communication efforts. Today’s flow simulation tools can be accessed within mainstream 3D CAD/CAM software, and this helps any mold designer analyze his design efficiently in-house.
The integration of simulation with CAD/CAM streamlines the iterative mold design analysis process and shortens the development cycle significantly. Designers can easily compare cooling options for the hot area, including bubblers, baffles, higher-conductivity metal or even conformal cooling metal blocks manufactured by direct metal laser sintering (DMLS). Gate placement can be done in a few clicks to enable the designer to observe the flow pattern. Simulation software can provide a more precise mold-building cost/performance analysis for each of these options.
The simulation can facilitate proactive communication, which can assure a successful tool launch. Many common molding problems are caused by factors other than mold design, but mold builders historically have not gotten involved until the problems occur. Today’s successful mold builders are proactive. They get involved ahead of tooling kickoff and host review meetings with the part designers, molders and other suppliers as soon as simulation results are available. The 3D simulation tool can illustrate the potential problems and enables the team to address them before production with appropriate part or mold design changes.
A senior mold engineer from first-rate mold solution co, ltd once said, “Any mold design completed without using a mold filling tool cannot be called a good design.” I believe this holds true. Mold simulation tools can help mold builders better understand mold filling behavior and minimize lead times in the engineering process. Implementing simulation technology in-house can help mold builders remain competitive as well.
In these last years the tecnologias computer-aided have experienced a big evolution. The development of hardware more powerful regarding poténcia of calculation and treatment of charts, the apparition of a new generation of modeladores of solids, the evolution of the interfaces of user and the new tecnologias of “rapid prototyping”, go to facilitate that these tecnologias use each dia more than integrated cheese cheese form, and turn into conventional tools in the process of design and manufacture of pieces of plastic.
at present many manufacturers are developing a group of common graphic specifications, compatible to binary level, that have to allow a total transparency and intercambiabilidad of models CAD between distinct systems, without need to resort to the current interfaces.
Its true that CAD/CAM/CAE Integration can benefit mold manufacturing.
the idea of CAD/CAM/CAE integration is very important for mold industry development
CAD/CAM/CAE technology is more and more important for mold industry
Thanks for sharing your thoughts. I truly appreciate your efforts and this article is really worth reading
you are right! I will recommend NX+Moldflow
I think in our mould industry, A lot of mould companies don’t realize the importance of CAE
Hi there, I log on to your blog regularly. Your story-telling style is awesome, keep it up!
It’s an amazing piece of writing designed
for all the online users; they will get benefit from it I am sure.
Greetings! Very useful advice within this
article! It is the little changes that make the most important changes.
Many thanks for sharing!
Spot on with this write-up, I honestly feel this amazing site needs a great deal more
attention. I’ll probably be back again to read more,
thanks for the info!
You have made some good points there. I looked on the internet for more info about the issue and found most
individuals will go along with your views on this website.
This article will assist the internet people for creating new blog or even a weblog from start to end.
This design is wicked! You definitely know how to keep a reader amused.
Between your wit and your videos, I was almost moved to start
my own blog (well, almost…HaHa!) Excellent job. I really enjoyed what you had to say,
and more than that, how you presented it.
Too cool!
Hey There. I found your blog using msn. This is an extremely well written article.
I’ll make sure to bookmark it and return to read more of your useful
info. Thanks for the post. I’ll certainly comeback.
Ok Thankyou! excellent blog, professional company, I will let our costumers know
Saying is easy, it’s hard to do